Housemate Range

STP50 / STP100

These peripheral turbine pumps produce high pressure and economical operation, with heads to 55M and flowes to 50LPM.  They are ideally suited for pumping clean water from rainwater collection tanks.  A brass stamped turbine – type impeller can handel high water temperature if used for pressure boosting.

JP60/JP100

An economical jet pump range. Self-priming to 6M, heads to 45M and flows to 60LPM. For large homes, lifting water from underground tanks, bores and clams. Injector/venturi design with closed implller, all of corrosion proof noryl.

STJ80/STJ120

High performance jet type for water supply to the largest homes.  These pumps can lift up to 8M vertically, accept water temperatures to 45PC and produce pressures to 600KPA. Large flow rates, quality constructions and silent operation makes these the ultimate household pump, with heads to 52M and flows out to 75LPM.

JSPA/INOX 100

An economy stainless steel body with corrosion resistant internals of impeller, diffuser, injector and nozzle of Noryl.  Heads to 52M and flows to 57LPM.  Self – priming on suction lifts up to 6M.

Electronic Controller

Commonly marketed as ‘Press control’, this advice will shut the pump down if the supply of water to it is interrupted, thereby avoiding damage due to dry running.  Additionally, it will keep the pump running continuously down to flows as low as 1-2LPM which avoids the annoyance of variations in shower water pressure due to cycling (pump switching on and off).  These controllers should only be used on pumps operating from ‘mains’ power supply.  Power supplies from inverters operating off battery banks from portable generators can result in component failure and consequently must be avoided.

STP080/ST0120

For horizontal applications such as supply to domestic premises, and can be equipped with electronic controllers or diaphragm tank.  Heads to 62M and flows to 90LPM with only .60 or .75w motor size, provides performance with economy.

STV300

A vertical multistage, single or three phase motors, and ideal for requirements where both high heads and high flows are needed.  With a quality grade stainless steel body and toatally enclosed, thermal protected motor, significant performance improvement is obtained over jet system models.  Max head is 81M, flows to 160LPM.

CM25V

A lightweight (6kg) 2 stroke pump unit. Flows to 100LPM (1,300 GPH) and heads to 35M (50PSI), self-priming with a viton seal assembly to permit pumping of spraying chemicals and diesel fuel. 1” ports and fully repairable construction.

40SP – Series 1 ½ “ High Pressure Firemate Pumps

Models with heads to 70M (100PSI) and flows to 400L (5,200 GPH). 3 way discharge head.  These pumps are typical ‘firemated’ with fire-fighting features.

50SP/80SP – Series 2” and 3” High Flow Pumps

High volume pumps for water transfer. Flow to 1,020LPM (13,000GHP) and heads to 37M (53PSI). Ideal for transferring large quantities from dams, filling tanks, low pressure irrigation.

Submersibles Range
A range of stainless steel ‘super subs’ designed and built to the highest standards to provide water under the most arduous operating conditions.  Matched to motors capable of working in aggressive water, these combination is 300 grade stainless steel or marine bronze for long working life.

Pumpmaster Pumps are the natural choice of bore drillers, pump installers and homeowners since 1888 and today’s pump range offers the best value for money anywhere.
Reliability – simple construction and heavy wall 303-grade stainless shell, guarantees longer life down the hole. 
Time proven. Floating stage impeller design proves 35 years ago is being used by all progressive manufactures. 
Beat sand and corrosion.  Tough Pumpmaster offers two years warranty against sane and corrosion as outlined in out specification sheet

East to service. Just slip in replacement cartridges.  Low cost maintenance.
Best value for money. Top grade product. Competitive pricing and two-year warranty. 113 years in the water pump industry.

These pumps offer – Large bearing surface area for long life in aggressive water Solid stainless steel discharge head and base Magnificent 316 stainless shaft with large hex drive for years of working life 30 different 4” pump models and 36 different 6” models means a pump to suit any application at maximum performance Precision molded high impact “Thermax” impellers float in diffuser stages of selected composite materials , for superior sand handling and run dry protection.

30 different 4” pump models and 70.6” pump models means a pump to suit any application at max performance . High tech “Super Rubber” wear face. Large ceramic top bearing for long life in aggressive water. 316 stainless diffuser housing. Patented fully floating impellers with unique component assemblies to eliminate axial thrust and give excellent sand handling.

Reliability – simple construction and heavy wall 304 grade stainless steel, guarantees longer life down the hole.  Time proven.  Floating stage impeller design proven 35 years ago is being used by all progressive manufactures.  Beat sand and corrosion.  Tough Pumpmaster offers two years against sand and corrosion as outlined in out specification sheet.

Easy to service. Just slip in replacement cartridges.  Low coast maintenance.  Best value for money. Top grade product. Competitive pricing and two year warranty. Years of experience in the water pump industry.
Solid stainless steel discharge head with built-in high flow check valve.
Solid stainless steel base bracket with built – in suction screen.